A Self-Sealing Modular Microfluidic System Using PDMS Blocks with Magnetic Connections -By Ecker et al., 2023.
Microfluidic chips are widely used in various fields ranging from medicine, science, and the food industry to environmental engineering. While gravitation plays a major role for liquids at the macroscopic scale, microfluidics are dominated by surface forces. Microfluidic flow is dominated by viscous forces and is laminar. Therefore, liquids behave in a more controlled and predictable way than in a macroscopic system. Numerous techniques enable the fabrication of microfluidic chips, including hot embossing, injection molding, laser ablation, 3D printing, and focused ion beam machining. While a single chip doesn’t allow the change of parts of the implemented microfluidic network, a modular system allows the rearrangement of components by splitting up the network into different parts separated into different blocks or modules. This can be achieved by using LEGO blocks.
Research shows that this approach works for open microfluidic networks. Additionally, when using polydimethylsiloxane (PDMS) as a base material, it can be used to fabricate organ-on-a-chip systems. In this work, Ecker and colleagues aim to create a modular microfluidic system using magnets and casted O-ring-like structures.
Two modular microfluidic blocks (MMBs) can be easily connected and disconnected using magnets. Each MMB contains small magnets; when you bring two MMBs together, the magnets align the connection interface and connect the blocks
FIGURE 1. Principle of the connection system. a) Modular microfluidic block with shown arrangement of the magnets on each port.
The goal was to produce a transparent module that would allow the visualisation of test fluids inside the channel structures. So, the researchers opted for using PDMS.
The manufacturing process of MMBs involves many steps. Initially, researchers created a template for the MMBs. This template serves as the foundation for crafting a polyurethane (PU) mould, essential for casting the MMBs. After that, PDMS is added to the mould, allowed to cure in an oven, and finally removed from the mould.
The researchers wanted to test if their flow sensor worked properly by comparing its measurements to those of a known commercial flow sensor. To achieve this, they used
pump to set different fluidic flows and measure the actual flow using both their
The researchers compared the measurements from the MMB sensor to those from the commercial sensor and found they were very similar, confirming the feasibility of the MMB sensor (Figure 2).
FIGURE 2. Calibration curves and measurements using the flow sensor MMB and a commercial flow sensor. a) Measured calibration curve with the corresponding linear fit. b) Measured calibration curve and its piecewise linear fit. c) and d) Example measurements using the commercial and the fabricated flow sensor for comparison.
The researchers tested some pumps and found they work well up to a certain speed, about 50 Hz. They also tested how well the system was connected by closing most openings, pouring water into the only open one, and measuring the pressure. They found that the system stayed sealed up to a certain pressure.
By using different measurement setups, the authors demonstrated the feasibility of the device.
Would you like to try similar experiments in your lab? Here's what you’ll need:
- a specialised microfluidic channel selector designed to work with an ExiGo pump.
We have options that suit all budgets. Request a quote or check out more options on our
A Self-Sealing Modular Microfluidic System Using PDMS Blocks with Magnetic Connections.
Maximising Efficiency and Performance: Using UniGo and ExiGo Pumps Together
Cellix's ExiGo Microfluidic syringe pump vs. conventional syringe pumps
Read the complete available background
All Posts
Inish Cell Analyser
Cell Counting & Viability
Transfection Efficiencies
Microfluidic pumps
Microfluidic chips
Droplet Generation
Organ-on-Chip
Thrombosis
Platelet aggregation
Inish Solutions
Microfluidic Solutions
VenaFlux Solutions
COVID-19
Cell adhesion & migration
Inflammation
Label Free Analysis
Gene Transfection
#CellixTech
We are Cellix
Cellix Out and About
µTas
Cyto Conf 2018
Inish Cell Sorter
Cell Sorting
Stem cells
Search
A Self-Sealing Modular Microfluidic System Using PDMS Blocks with Magnetic Connections -By Ecker et al., 2023.
cellixmarketing
Feb 12, 2024
2 min read
Background
Microfluidic chips are widely used in various fields ranging from medicine, science, and the food industry to environmental engineering. While gravitation plays a major role for liquids at the macroscopic scale, microfluidics are dominated by surface forces. Microfluidic flow is dominated by viscous forces and is laminar. Therefore, liquids behave in a more controlled and predictable way than in a macroscopic system. Numerous techniques enable the fabrication of microfluidic chips, including hot embossing, injection molding, laser ablation, 3D printing, and focused ion beam machining. While a single chip doesn’t allow the change of parts of the implemented microfluidic network, a modular system allows the rearrangement of components by splitting up the network into different parts separated into different blocks or modules. This can be achieved by using LEGO blocks.
Research shows that this approach works for open microfluidic networks. Additionally, when using polydimethylsiloxane (PDMS) as a base material, it can be used to fabricate organ-on-a-chip systems. In this work, Ecker and colleagues aim to create a modular microfluidic system using magnets and casted O-ring-like structures.
Methods
Fabrication Process
Two modular microfluidic blocks (MMBs) can be easily connected and disconnected using magnets. Each MMB contains small magnets; when you bring two MMBs together, the magnets align the connection interface and connect the blocks
(Figure 1)
.
FIGURE 1. Principle of the connection system. a) Modular microfluidic block with shown arrangement of the magnets on each port.
The goal was to produce a transparent module that would allow the visualisation of test fluids inside the channel structures. So, the researchers opted for using PDMS.
The manufacturing process of MMBs involves many steps. Initially, researchers created a template for the MMBs. This template serves as the foundation for crafting a polyurethane (PU) mould, essential for casting the MMBs. After that, PDMS is added to the mould, allowed to cure in an oven, and finally removed from the mould.
Function of the Flow Sensor
The researchers wanted to test if their flow sensor worked properly by comparing its measurements to those of a known commercial flow sensor. To achieve this, they used
Cellix's ExiGo syringe
pump to set different fluidic flows and measure the actual flow using both their
flow sensor
and a commercial flow sensor.
Results
The researchers compared the measurements from the MMB sensor to those from the commercial sensor and found they were very similar, confirming the feasibility of the MMB sensor (Figure 2).
FIGURE 2. Calibration curves and measurements using the flow sensor MMB and a commercial flow sensor. a) Measured calibration curve with the corresponding linear fit. b) Measured calibration curve and its piecewise linear fit. c) and d) Example measurements using the commercial and the fabricated flow sensor for comparison.
Other experiments in this study
The researchers tested some pumps and found they work well up to a certain speed, about 50 Hz. They also tested how well the system was connected by closing most openings, pouring water into the only open one, and measuring the pressure. They found that the system stayed sealed up to a certain pressure.
Conclusion
By using different measurement setups, the authors demonstrated the feasibility of the device.
How to get started
Would you like to try similar experiments in your lab? Here's what you’ll need:
ExiGo Pump
– a pulse-free syringe pump for low-flow microfluidic applications.
Flow sensors
– allows monitoring of pump flow rate.
ExiGo Manifold
- a specialised microfluidic channel selector designed to work with an ExiGo pump.
We have options that suit all budgets. Request a quote or check out more options on our
eShop!
References
Ecker, Rafael, et al. "
A Self-Sealing Modular Microfluidic System Using PDMS Blocks with Magnetic Connections.
" IEEE Access (2023).
Microfluidic pumps
Droplet Generation
Microfluidic chips
Recent Posts
See All
Maximising Efficiency and Performance: Using UniGo and ExiGo Pumps Together
ExiGo Manifold: maximizing the flexibility of your microfluidic setup
Cellix's ExiGo Microfluidic syringe pump vs. conventional syringe pumps
For illustrations, downloads and the latest updates, visit the original published page.
View original Cellix reference